The free-hand quilting foot set, steplessly adjustable & individually replaceable for the following models only:W6 N 2800 ExklusiveW6 N 3300 ExklusiveW6 N 5000W6 N 5000 ExklusiveW6 N 8000W6 N 8000 ExklusiveW6 N 9000 QPLW6 N 9500C QPLThe steplessly adjustable and replaceable quilting set consisting of:Presser foot holder (adapter)Open quilting foot sole (replaceable)Closed quilting foot sole (replaceable)Ruler foot sole (replaceable)Free-hand Echoquilter sole (replaceable) Information on the replaceable open quilting foot soleApplication: This foot provides a clear view of the material. It makes the free guidance for free-hand embroidery or darning even more precise. Also ideally suited for guiding thick quilting and free-hand quilting pieces.Tip 1 for quilting: Select a high sewing machine speed; this is the only way to ensure that the sewing piece can be easily guided into turns.Tip 2 for needle painting: Please put sufficient stabiliser under the fabric or use an embroidering frame. This prevents any distortion from occurring while sewing.Sewing machine setting:Stitch: Straight stitchLower the feed dogsManual for attaching the replaceable open quilting foot soleRemove the slotted screw from the presser foot holder e.g. by means of the round screwdriver The presser foot has been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw, place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter)Fix the sole in place on the rear of the presser foot holder by means of the round screwdriverThe replaceable open quilting foot sole has been mountedInformation on the replaceable closed quilting foot soleApplication: This foot enables free guidance for free-hand embroidery or darning. It is also ideal for quilting and free-hand quilting.Tip 1 for quilting: Select a high sewing machine speed; this is the only way to ensure that the sewing piece can be easily guided into turns.Tip 2 for needle painting: Please put sufficient stabiliser under the fabric or use an embroidering frame. This prevents any distortion from occurring while sewing.Sewing machine setting:Stitch: Straight stitch Lower the feed dogs  Manual for attaching the replaceable closed quilting foot sole Remove the slotted screw from the presser foot holder  e.g. by means of the round screwdriver The presser foot has been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw, place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter)Fix the sole in place on the rear of the presser foot holder (adapter) by means of the round screwdriver The replaceable closed quilting foot sole has been mounted Information on the replaceable ruler foot soleThe special sewing machine ruler foot is always circular and freely adjustable. The distance between the needle and the ruler foot edge is 1/4 inch. The edge is several millimeters high and can thus be guided along the W6 WERTARBEIT ruler/quilting bars comfortably and neatly. The special presser foot enables bar-based quilting.W6 recommends using a large and comfortable extension table from the W6 accessories range for relieving the tension on the fabric and for guiding the quilting work in a straight line in all directions at the barNeedle: W6 WERTARBEIT quilting needle 90W6 ruler/quilting barThread: Lint-free W6 WERTARBEIT thread which can be easily tensioned and is available in 415 colours, offering an unbeatable price-performance ratioApplication: Use a 3-layered fabric sandwich (cotton, thinner volume fleece, cotton) for quilting.Please note: The thicker the volume fleece selected, the more difficult it is to freely guide the ruler foot!Please note: It must be possible to easily move the quilt sandwich.Safety note: Never lower the needle while the ruler foot is raised; doing so may lead to damage to the needle bar or the ruler foot. We recommend using quilting gloves.Machine setting:Lower the feed dogsAdjust the attached sewing machine ruler foot to the thickness of the quiltPlace the quilt sandwich under the ruler foot in order to do soLower the sewing machine ruler footAdjust and/or re-adjust the ruler foot height with the fastening screw such that the bottom of the ruler foot only has light contact with the quilt sandwichPlease note: When using volume fleeces which are too thick, an even guidance of the quilting piece is not possibleSet the straight stitch; set the needle in the central positionW6 recommends using a large, comfortable extension table from the W6 accessories range for relieving the tension on the fabric and for guiding the quilting pieces in a straight line in all directions at the ruler/barNeedle: W6 WERTARBEIT quilting needle 90Thread tension set to 4 or as requiredThread: Lint-free W6 WERTARBEIT thread which can be easily tensioned and is available in 415 colours, offering an unbeatable price-performance ratioManual for attaching the ruler foot soleRemove the slotted screw from the presser foot holder  e.g. by means of the round screwdriver The presser foot has now been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw Place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter) Fix the sole in place on the rear of the presser foot holder (adapter) by means of the round screwdriverThe replaceable ruler sole has been mounted Information on the replaceable free-hand echoquilter soleThe echoquilting foot is suited for producing quilting lines within even distances around a motif or an application. The red markings on the transparent presser foot will help you in creating the ripping effect, maintaining even distances and thus creating certain effects.This special quilting foot will help you create many different hobby pieces.The quilting foot is ideally suited for echo quilting/shadow quilting and free-hand quiltingWith this quilting foot, nothing stands in the way of freely guided embroideryStarting from the centre of the plate, the dimensions of the free-hand echo quilting foot are as follows:6.4 mm (approx. 1/4 inch)9.5 mm (approx. 3/8 inch)Manual for attaching the replaceable free-hand echo quilting soleRemove the slotted screw from the presser foot holder  e.g. with the round screwdriver The presser foot has been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw Place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter) Fix the sole in place on the rear of the presser foot holder (adapter) by means of the round screwdriverThe replaceable free-hand echo quilting sole has been mounted

Only available for model W6 N 707D, 9500C QPL and 9000 QPLThe flexible metal edge guide with a length of 6 cm enables you to quickly and effortlessly sew straight seams and hems. This metal edge guide can be attached to a sewing machine using a white metal screw. To remove the metal edge guide, loosen the white screw.We are confident that you will enjoy using this small device.The metal edge guide may be attached to the following models:W6 N 707D free-arm coverlockW6 N 9500C QPL long-armW6 N 9000 QPL long-armW6 sewing machine N 707D free-arm coverlock:How to attach the metal edge guide to Model W6 N 707D free-armTo select the correct distance, please choose one of the two holes located on the right-hand side of the machine's needle plate. (Pictures 01a and 01b)Picture 01a - left holePicture 01b - right holeThe maximum distance between the rightmost needle and the left hole is about 1.0 cm. Please take a look at the picture below.The minimum distance between the rightmost needle and the left hole is about 0.5 cm. Please take a look at the picture below.The maximum distance between the rightmost needle and the right hole is about 3.5 cm. Please take a look at the picture below.The minimum distance between the rightmost needle and the right hole is about 0.5 cm. Please take a look at the picture below.W6 sewing machine N 9500C QPL and W6 sewing machine N 9000 QPL:How to attach the metal edge guide to Model W6 N 9500C QPL and W6 N 9000 QPLTo select the correct distance, please choose one of the two holes located on the right-hand side of the machine's needle plate. (Pictures 01a and 01b)Picture 01a - left holePicture 01b - right holeThe maximum distance between the needle (central position) and the left hole is about 3.3 cm. Please take a look at the picture below.Note: To avoid damaging the machine's case, please place a felt disc below the metal edge guide's right side. You can find the felt disc inside the machine's standard accessory set.The minimum distance between the needle (central position) and the left hole is about 1.0 cm. Please take a look at the picture below.Note: To avoid damaging the machine's case, please place a felt disc below the metal edge guide's right side. You can find the felt disc inside the machine's standard accessory set.The maximum distance between the needle (central position) and the right hole is about 4.5 cm. Please take a look at the picture below.The minimum distance between the needle (central position) and the right hole is about 1.0 cm. Please take a look at the picture below.Note: To avoid damaging the machine's case, please place a felt disc below the metal edge guide's right side. You can find the felt disc inside the machine's standard accessory set.

W6 sewing machine ruler foot, freely adjustable. Only for:W6 N 2800 ExklusiveW6 N 3300 ExklusiveW6 N 5000W6 N 5000 ExklusiveW6 N 8000W6 N 8000 ExklusiveW6 N 9000 QPLW6 N 9500C QPLThe special sewing machine ruler foot is always circular and freely adjustable. The distance between the needle and the ruler foot edge is 1/4 inch. The edge is several millimeters high and can thus be guided along the W6 WERTARBEIT ruler/quilting bars comfortably and neatly. The special presser foot enables bar-based quilting.W6 recommends using a large and comfortable extension table from the W6 accessories range for relieving the tension on the fabric and for guiding the quilting work in a straight line in all directions at the barNeedle: W6 WERTARBEIT quilting needle 90W6 ruler/quilting barThread: Lint-free W6 WERTARBEIT thread which can be easily tensioned and is available in 415 colours, offering an unbeatable price-performance ratioApplication: Use a 3-layered fabric sandwich (cotton, thinner volume fleece, cotton) for quiltingPlease note: The thicker the volume fleece selected, the more difficult it is to freely guide the ruler foot!Attachment of the sewing machine ruler foot:Remove the standard foot with the presser foot holder, including fastening screw. Carefully attach the ruler foot directly at the bar using the fastening screw.Put the quilt sandwich under the ruler foot and lower it.Adjust the height of the ruler foot to the quilt sandwich using the adjusting screw.Please note: It must be possible to easily move the quilt sandwich.Safety note: Never lower the needle while the ruler foot is raised; doing so may lead to damage to the needle bar or the ruler foot.We recommend using quilting gloves.Machine setting:Lower the feed dogs Adjust the attached sewing machine ruler foot to the thickness of the quilt Place the quilt sandwich under the ruler foot in order to do so Lower the sewing machine ruler foot Adjust and/or re-adjust the ruler foot height with the fastening screw such that the bottom of the ruler foot only has light contact with the quilt sandwich Please note: When using volume fleeces which are too thick, an even guidance of the quilting piece is not possible Set the straight stitch, the stitch length must not be below 2.5; set the needle in the central position W6 recommends using a large, comfortable extension table from the W6 accessories range for relieving the tension on the fabric and for guiding the quilting pieces in a straight line in all directions at the ruler/barNeedle: W6 WERTARBEIT quilting needle 90Thread tension set to 4 or as requiredThread: Lint-free W6 WERTARBEIT thread which can be easily tensioned and is available in 415 colours, offering an unbeatable price-performance ratio

Presser foot for all W6 WERTARBEIT sewing machines.  The W6 N 2000 also requires the adapter.Sew together the pieces of fabric using stitch pattern no. 1, with a seam allowance of 1/4 inch (6.3 mm)

The circulatory sewing attachment can be used to create unique patterns and motifs. Circles, flowers, petals as well as creative and outlandish graphical patterns in different sizes can be combined to complex patterns. Give free rein to your creativity.The W6 WERTARBEIT circulatory sewing attachment can create circles with diameters of 6 to 26 cm.Indication in inch and cm. This corresponds to 2.5 to 10.25 inches.Scope of delivery:Metal circulatory sewing attachment with pink pinPink pinTemplates included:Blue template for sewing circlesBlue template for stitching a flower with 4 petalsBlue template for stitching a flower with 6 petalsFixing screws - amount: 2

Presser foot for all W6 WERTARBEIT sewing machines.Application: This foot enables free guidance for free-hand embroidery or darning. It is also ideal for quilting and free-hand quilting.Screw-on the shaft of the presser foot.Use the screw of the shaft of the presser foot to tighten the darning embroidery foot at the needle bar.Let the right bracket run over the right needle bar.Tip 1: Select the full sewing machine speed; this is the only way to ensure that the sewing piece can be easily guided into turns.Tip 2: Please put sufficient stabiliser under the fabric or use an embroidering frame. This prevents any distortion from occurring while sewing.Sewing machine setting:Stitch: Straight stitch or zigzag (width 3-5)Stitch length: not too narrow, as this hinders the sewing machine from rendering a good forward conveyance.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.This foot has a hollow and transparent middle piece. This can be used for easily guiding applications, darning work and decorative seams, curves or corners.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.A popular foot for patchwork that ensures a neat guidance of the 1/4 seam Additionally, this foot can be used for ditch sewing and topstitching. This foot enables positioning, for example, a straight stitch very close to an edge. A must-have for patchworkers, quilters and hobby sewists!Application: Thanks to the continuously adjustable needle offset (stitch width selection), the needle can be moved along the edge of the woven band to the left or right. The protruding long shaft guide enables an easy and secure gliding, without slipping from the sewn edge. This tool is makes sewing patchwork and quilts a whole lot easier and more enjoyable.Sewing machine setting:Stitches: freely selectable, e.g. straight stitch Stitch length: 3 to 3.5The steplessly adjustable needle position is set by selecting the stitch width:e.g. W6 N 3300 ExklusiveStitch width 0 = needle position outer leftStitch width 3.5 = needle position approx. centralStitch width 7.0 = needle position outer righte.g. W6 N 1235/61, programme AStitch width 0 = needle position outer leftStitch width 5 = Needle position approx. centrale.g. W6 N 1800Programme A = Needle position approx. centralProgramme B = Needle position outer leftPlease note:The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: Special foot for producing high-quality decorative stitches, tight zigzag stitches and satin seams. The special guide at the bottom enables an unobstructed sliding-through of stitches.Sewing machine setting:Stitch: Decorative stitches, satin stitchesStitch length: 3-5Tip: Place the stabiliser under the sewing piece to prevent the fabric from widening.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Special high quilting foot for W6 sewing machinesThe W6 special high quilting foot with its extremely short shaft is intended for quilting with thick volume fleece and raised seam crossings. This quilting foot leads to an ideal quilting result with free-hand quiltingW6 tip: When quilting, the upper thread tension must always be increased to 4-7.Application:   Screw-on the shaft of the presser foot.Use the screw of the shaft for tightening the special high quilting foot on the left-hand side of the needle bar.Let the right metal bracket of the special quilting foot run across the right needle bar.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines.The walking foot is used wherever several layers of different material types and/or fabrics with different surface structures are to be sewn together. The special toothing of the walking foot supports the sewing process and prevents the sagging or displacement of the fabric. The quilting bar is very helpful for ensuring straight lines when quilting. The quilting bar can be inserted into the walking foot on the right.  For quilting (essential)For top-stitching e.g. shirt collars For decorative stitches  For sewing on bands For heavy fabrics such as jeans or leather 

W6 walking foot with replaceable presser feet (also referred to as “soles”) Only suitable for the models W6 N 9000/9500C QPLThe W6 walking foot with replaceable soles is ideally suitable for quilting/patchwork and for stretchable fabrics or fabrics that tend to slip. This special walking foot comes with three soles which can be easily replaced.Standard soleOpen sole for a better viewDitch sole with edgeAdditionally, the scope of delivery includes two exclusive quilting bars with a length of 4.5 inches (approx. 11.43 cm). These can each be attached as spacers on the right or left-hand side of the walking foot.Specific technical features compared to a regular walking foot:¼ inch cut-out on the left and right-hand inner face of the sole. This walking foot is thus perfectly suitable for quilting/patchwork and sewing difficult fabrics, which are very elastic or have poor sliding propertiesThe rubber feed dogs integrated into the presser foot ensure smooth movement of the fabric and protect it against abrasionA vertical ¼ inch mark attached at the front of the different soles enables precise sewing, including on corners.