The cover foot set consists of:1. Transparent foot, only for cover W6 N 707 D free-armThis cover foot is completely transparent, making the identification of alignment lines for stepping incredibly easy. The fabric is applied correctly; you have full control of the seam and can achieve an ideal sewing result. PHOTO bottom: Transparent foot cover2. Individual turning foot only for cover W6 N 707 D free-armThis cover foot is transparent. The individual turning foot can help you create perfect hem seams with the chain stitch seam or e.g. a narrow or wide cover stitch. Make sure to iron the fabric carefully to achieve a nice fabric contact edge. If applicable, you may also have to fix the fabric in a straight line at the hem by means of a manual stitch so that the fabric cannot move around when covering. The hem width varies depending on the selection of the cover stitch, e.g. wide cover stitch, narrow cover stitch. It is possible to create cover seams of approx. 4 mm to 14 mm from the hem edge, depending on the cover stitch selected.3. Individual turning foot with guide line for lace edging, only for cover W6 N 707 D free-armThis cover foot is transparent. The individual turning foot can be used to create perfect hem seams with the chain stitch seam or e.g. a narrow or wide cover stitch and sew on a lace edging at the same time, in the same work step. Make sure to iron the fabric carefully to achieve a nice fabric contact edge. If applicable, you may also have to fix the fabric in a straight line at the hem by means of a manual stitch so that the fabric cannot move around when covering. The hem width varies depending on the selection of the cover stitch, e.g. wide cover stitch or narrow cover stitch. It is possible to create cover seams of 4 mm to 14 mm from the hem edge, depending on the cover stitch selected.4. Cord foot only for cover W6 N 707 D free-arm This cover presser foot is transparent. It can be used for producing great decorative seams with a cord. A cord with a thickness of less than 2.5 mm can be securely guided into the central guide rail. To securely guide the cord under the fabric, we recommend using the transparent cord guide plate.5. Lace presser foot for the cover W6 N 707 D free-armThe transparent lace presser foot can be used for comfortably and easily sewing on lace edging by means of a special guide rail on the right-hand side. Lace edging can be sewn up to a maximum height of 1.5 mm by means of the transparent cover foot.6. Band edging foot for the cover W6 N 707 D free-armThe transparent band edging foot can be used with unfolded bias bands with widths of up to 4.6 cm inserted into its guide spiral.7. Belt loop foot only for cover W6 N 707 D free-armThe transparent cover foot can be used for making spaghetti straps for summer dresses or belt loops.Download: Presser foot manual

The free-hand embroidering frame W6, 12.7 cm (5 inches), is used for freely guiding creative patterns, motifs and letters.Application: Fix the fabric in place with W6 self-adhesive stabiliser at the bottom.Clamp in the underlaid fabric without any folds and pull it tightly in the free-hand embroidering frameThe underlaid fabric can be ideally guided and turned now by means of the free-hand embroidering frameW6 tip:The W6 sewing machine embroidery, darning and free-hand quilting foot is ideally suited for free guiding.This special foot has hardly any contact surface and simplifies the creative guidance of patterns, motifs and letters.The sewing instructions for needle painting with the sewing machine are provided in our W6-WERTARBEIT sewing projects:Needle painting with the sewing machine

The free-hand quilting foot set, steplessly adjustable & individually replaceable for the following models only:W6 N 2800 ExklusiveW6 N 3300 ExklusiveW6 N 5000W6 N 5000 ExklusiveW6 N 8000W6 N 8000 ExklusiveW6 N 9000 QPLW6 N 9500C QPLThe steplessly adjustable and replaceable quilting set consisting of:Presser foot holder (adapter)Open quilting foot sole (replaceable)Closed quilting foot sole (replaceable)Ruler foot sole (replaceable)Free-hand Echoquilter sole (replaceable) Information on the replaceable open quilting foot soleApplication: This foot provides a clear view of the material. It makes the free guidance for free-hand embroidery or darning even more precise. Also ideally suited for guiding thick quilting and free-hand quilting pieces.Tip 1 for quilting: Select a high sewing machine speed; this is the only way to ensure that the sewing piece can be easily guided into turns.Tip 2 for needle painting: Please put sufficient stabiliser under the fabric or use an embroidering frame. This prevents any distortion from occurring while sewing.Sewing machine setting:Stitch: Straight stitchLower the feed dogsManual for attaching the replaceable open quilting foot soleRemove the slotted screw from the presser foot holder e.g. by means of the round screwdriver The presser foot has been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw, place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter)Fix the sole in place on the rear of the presser foot holder by means of the round screwdriverThe replaceable open quilting foot sole has been mountedInformation on the replaceable closed quilting foot soleApplication: This foot enables free guidance for free-hand embroidery or darning. It is also ideal for quilting and free-hand quilting.Tip 1 for quilting: Select a high sewing machine speed; this is the only way to ensure that the sewing piece can be easily guided into turns.Tip 2 for needle painting: Please put sufficient stabiliser under the fabric or use an embroidering frame. This prevents any distortion from occurring while sewing.Sewing machine setting:Stitch: Straight stitch Lower the feed dogs  Manual for attaching the replaceable closed quilting foot sole Remove the slotted screw from the presser foot holder  e.g. by means of the round screwdriver The presser foot has been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw, place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter)Fix the sole in place on the rear of the presser foot holder (adapter) by means of the round screwdriver The replaceable closed quilting foot sole has been mounted Information on the replaceable ruler foot soleThe special sewing machine ruler foot is always circular and freely adjustable. The distance between the needle and the ruler foot edge is 1/4 inch. The edge is several millimeters high and can thus be guided along the W6 WERTARBEIT ruler/quilting bars comfortably and neatly. The special presser foot enables bar-based quilting.W6 recommends using a large and comfortable extension table from the W6 accessories range for relieving the tension on the fabric and for guiding the quilting work in a straight line in all directions at the barNeedle: W6 WERTARBEIT quilting needle 90W6 ruler/quilting barThread: Lint-free W6 WERTARBEIT thread which can be easily tensioned and is available in 415 colours, offering an unbeatable price-performance ratioApplication: Use a 3-layered fabric sandwich (cotton, thinner volume fleece, cotton) for quilting.Please note: The thicker the volume fleece selected, the more difficult it is to freely guide the ruler foot!Please note: It must be possible to easily move the quilt sandwich.Safety note: Never lower the needle while the ruler foot is raised; doing so may lead to damage to the needle bar or the ruler foot. We recommend using quilting gloves.Machine setting:Lower the feed dogsAdjust the attached sewing machine ruler foot to the thickness of the quiltPlace the quilt sandwich under the ruler foot in order to do soLower the sewing machine ruler footAdjust and/or re-adjust the ruler foot height with the fastening screw such that the bottom of the ruler foot only has light contact with the quilt sandwichPlease note: When using volume fleeces which are too thick, an even guidance of the quilting piece is not possibleSet the straight stitch; set the needle in the central positionW6 recommends using a large, comfortable extension table from the W6 accessories range for relieving the tension on the fabric and for guiding the quilting pieces in a straight line in all directions at the ruler/barNeedle: W6 WERTARBEIT quilting needle 90Thread tension set to 4 or as requiredThread: Lint-free W6 WERTARBEIT thread which can be easily tensioned and is available in 415 colours, offering an unbeatable price-performance ratioManual for attaching the ruler foot soleRemove the slotted screw from the presser foot holder  e.g. by means of the round screwdriver The presser foot has now been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw Place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter) Fix the sole in place on the rear of the presser foot holder (adapter) by means of the round screwdriverThe replaceable ruler sole has been mounted Information on the replaceable free-hand echoquilter soleThe echoquilting foot is suited for producing quilting lines within even distances around a motif or an application. The red markings on the transparent presser foot will help you in creating the ripping effect, maintaining even distances and thus creating certain effects.This special quilting foot will help you create many different hobby pieces.The quilting foot is ideally suited for echo quilting/shadow quilting and free-hand quiltingWith this quilting foot, nothing stands in the way of freely guided embroideryStarting from the centre of the plate, the dimensions of the free-hand echo quilting foot are as follows:6.4 mm (approx. 1/4 inch)9.5 mm (approx. 3/8 inch)Manual for attaching the replaceable free-hand echo quilting soleRemove the slotted screw from the presser foot holder  e.g. with the round screwdriver The presser foot has been removed Mount the presser foot holder (adapter) by means of the round screwdriver and manually tighten the slotted screw Place the replaceable sole in the desired position. Use your index finger to press the sole into the longitudinal metal bracket of the presser foot holder (adapter) Fix the sole in place on the rear of the presser foot holder (adapter) by means of the round screwdriverThe replaceable free-hand echo quilting sole has been mounted

Only available for model W6 N 707D, 9500C QPL and 9000 QPLThe flexible metal edge guide with a length of 6 cm enables you to quickly and effortlessly sew straight seams and hems. This metal edge guide can be attached to a sewing machine using a white metal screw. To remove the metal edge guide, loosen the white screw.We are confident that you will enjoy using this small device.The metal edge guide may be attached to the following models:W6 N 707D free-arm coverlockW6 N 9500C QPL long-armW6 N 9000 QPL long-armW6 sewing machine N 707D free-arm coverlock:How to attach the metal edge guide to Model W6 N 707D free-armTo select the correct distance, please choose one of the two holes located on the right-hand side of the machine's needle plate. (Pictures 01a and 01b)Picture 01a - left holePicture 01b - right holeThe maximum distance between the rightmost needle and the left hole is about 1.0 cm. Please take a look at the picture below.The minimum distance between the rightmost needle and the left hole is about 0.5 cm. Please take a look at the picture below.The maximum distance between the rightmost needle and the right hole is about 3.5 cm. Please take a look at the picture below.The minimum distance between the rightmost needle and the right hole is about 0.5 cm. Please take a look at the picture below.W6 sewing machine N 9500C QPL and W6 sewing machine N 9000 QPL:How to attach the metal edge guide to Model W6 N 9500C QPL and W6 N 9000 QPLTo select the correct distance, please choose one of the two holes located on the right-hand side of the machine's needle plate. (Pictures 01a and 01b)Picture 01a - left holePicture 01b - right holeThe maximum distance between the needle (central position) and the left hole is about 3.3 cm. Please take a look at the picture below.Note: To avoid damaging the machine's case, please place a felt disc below the metal edge guide's right side. You can find the felt disc inside the machine's standard accessory set.The minimum distance between the needle (central position) and the left hole is about 1.0 cm. Please take a look at the picture below.Note: To avoid damaging the machine's case, please place a felt disc below the metal edge guide's right side. You can find the felt disc inside the machine's standard accessory set.The maximum distance between the needle (central position) and the right hole is about 4.5 cm. Please take a look at the picture below.The minimum distance between the needle (central position) and the right hole is about 1.0 cm. Please take a look at the picture below.Note: To avoid damaging the machine's case, please place a felt disc below the metal edge guide's right side. You can find the felt disc inside the machine's standard accessory set.

W6 Fingerschutz für W6 Nähmaschinen aller Art Ein Fingerschutz dient Ihrer Sicherheit beim Nähen und wird direkt mit der Schraube am Nähfußhalter der W6 befestigt. Ihr Vorteil gegenüber eines herkömmlichen Fingerschutzes:Der Einfädler lässt sich ohne Probleme benutzen und ist in jeder Lage bedienbar Er soll Ihre Finger vor dem Berühren der Nähnadel schützen Ein Einklemmen der Finger unter der Feststellklammer sollte fast ausgeschlossen werden Ein Fingerschutz sollte bei Kindern stets verwendet werden, wenn sie beim Nähen unterrichtet werden Bitte beachten Sie, dass Kinder und Jugendliche stets unter Aufsicht eines Erwachsenen nähen sollten Es kann sein, dass Sie nach Vorschrift der Berufsgenossenschaft Vorkehrungen bezüglich des Fingerschutzes treffen sollten

W6 Ersatzteil:W6 N 1800W6 N 1615W6 N 1235/61W6 N 1233/61

W6 Ersatzteil: W6 N 3300 Exkl. W6 N 3300 Pro W6 N 5000 W6 N 5000 Exkl. W6 N 5000 Pro W6 N 6000 W6 N 8000 W6 N 8000 Exkl.

Presser foot for all W6 WERTARBEIT sewing machines.  The W6 N 2000 also requires the adapter.Sew together the pieces of fabric using stitch pattern no. 1, with a seam allowance of 1/4 inch (6.3 mm)

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: This foot is made of a special synthetic resin and cannot stick to fabrics as is the case with some metal feet. It can be used with paint material, light tarpaulin, leather, vinyl and imitation leather.Sewing machine setting:Stitch: Straight stitch, zigzag or elastic zigzagStitch length: 3-4Thread tension: 4 or automatic thread tensionPlease note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: This foot is made of a special synthetic resin and cannot stick to fabrics as is the case with some metal feet. Our special anti-stick roller foot combines the advantages of an anti-stick foot with the roller function of a roller foot. You are thus well equipped for working with very difficult materials. The roller function sews and/or rolls easily over fabrics that usually have poor sliding properties, while uneven spots are levelled out. No marks are left on the fabric. You can use it for a broad range of materials: e.g. paint materials, light tarpaulin, leather, vinyl and imitation leather.Sewing machine setting:Stitch: Straight stitch, zigzag or elastic zigzagStitch length: 3-4Thread tension: 4Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: The bias band binder can be used to simply fold and sew on up to 24-mm non-seamed bands, resulting in a single seamed bias band. Alternatively, you can also use pre-seamed bias bands to create double seamed bias band.The funnel-shaped guide forms the band and positions it around the edge of the fabric; the band is sewed on at the bias band at the fabric.The aesthetic impact of the edge seam can be enhanced with embellishment and decorative stitches.Sewing machine setting:Stitch: Straight stitchStitch length: 3-4Procedure:Diagonally cut the bias band in the beginning.Pull the bias band into the spiral of the bias band binder, e.g. with the help of the tip of a pair of scissors.Then pull the bias band out towards the rear.Set the needle position (e.g. via the stitch width setting) such that the needle pierces the fabric approx. 1-2 mm away from the folded bias band edge.Pull the cut edge of the fabric between the bias band in the designated slot of the bias band binder.This places the bias band around the fabric edge.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: For all high-quality skirt or trouser hems which have an invisible special stitching on the visible exterior, approximately 2.5 cm away from the edge. This fixes the inner hem and ensures that it cannot fold down anymore. Sewing machine setting: Use the blind stitch sewing programme of your W6 for sewing the blind stitch (see manual).  Lay down the fabric with the reverse side facing upwards. Fold the edge of the fabric to the desired hem width, as shown in the figure. Iron and tack the fabric and/or hem before sewing to guarantee a neat sewing result.Insert the blind hem foot. Position the fabric such that the presser foot guide lies against the hem edge and lower the presser foot lifter.The needle should pierce the fabric as close as possible to the edge of the fold. Note: Aligning the insertion position; the right and left needle insertion position can be determined by rotating the screw at the blind hem foot.  If applicable, remove the tacking thread and turn over the fabricBlind stitches cannot be sewn if the left-hand needle insertion point is not on the hem. If the needle grasps too much of the hem, a large and unsightly seam appears on the front side of the fabric.Stitch: Straight stitchStitch length: 3-3.5Stitch width: please adjust the needle position to the foot; if applicable, change the needle position via the stitch width.Thread tension: automatic or to 4 for the mechanical models (W6 N 1800, W6 N 1615, W6 N 1233/61, W6 N 1235/61)Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Sewing-on buttons is rather boring, time-consuming work This presser foot allows you to sew on two or four-hole buttons of different sizes without any problems. Simply adjust the stitch width to the distance between the button holes and your sewing machine will do the rest.Application: A perfect presser foot for easily sewing on buttons with the sewing machine. With this presser foot, buttons can be sewn on securely and quickly. The button is fixed and cannot slip.Sewing machine setting:Stitch: Set the stitch programme for sewing on buttons, if available, or the zigzag programmeStitch width: depending on buttonSewing machine setting: Stitch length: 0Stitch width: Set the zigzag programme to the correct width of the button hole bars (or holes) Important note:  Put the feed dogs cover on the feed dogs if using mechanical sewing machines (W6 N 1800, W6 N 1615, W6 N 1235/61, W6 N 1233/61) and lower the feed dogs when using computer-controlled sewing machines. Please note: For raising the feed dogs when using computer-controlled sewing machines, please refer to the operating manual Sewing: Place the button on the fabric in the desired position and sew on the button with a few stitches.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

The circulatory sewing attachment can be used to create unique patterns and motifs. Circles, flowers, petals as well as creative and outlandish graphical patterns in different sizes can be combined to complex patterns. Give free rein to your creativity.The W6 WERTARBEIT circulatory sewing attachment can create circles with diameters of 6 to 26 cm.Indication in inch and cm. This corresponds to 2.5 to 10.25 inches.Scope of delivery:Metal circulatory sewing attachment with pink pinPink pinTemplates included:Blue template for sewing circlesBlue template for stitching a flower with 4 petalsBlue template for stitching a flower with 6 petalsFixing screws - amount: 2

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Nearly invisible zippers, just like in mass-produced clothing – this is guaranteed with the special foot for concealed zippers.  The two grooves under the presser foot provide an ideal guide for the toothed rows of the zipper. Nothing can slip anymore! Use in high-quality evening wear and trendy sewn pieces Tip: The purchased, concealed zipper must be longer than the opening slit in the clothing.

Cord presser foot for W6 N 1800, 1615, 1235/61 and 2000 sewing machineApplication:Set the stitch pattern, e.g. zigzag, with the stitch width 4.0 to 5.0 (depending on the thickness of the cord) Slide the cord from the right-hand side below the central groove of the black foot bracket of the cord presser foot. Pull the cord until the cord protrudes about 5 cm behind the cord presser footSelect the stitch width such that the stitch is exactly above the cordLower the presser foot and sew very slowly while guiding the cord with your handTriple cord:Set the stitch pattern, e.g. zigzag, with the stitch width 6.0 to 7.0 (depending on the thickness of the cord) Slide the three cords under the three grooves of the black foot bracket of the cord presser footPull the cords until the cords protrude about 5 cm behind the cord presser footLower the presser foot and sew very slowly while guiding the cords with your handW6 Tip:With double cords, proceed as with tripe cords, e.g. select a decorative stitch which covers the two cords based on the stitch width.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: The cording foot with grooves is used for decorating blouses, pillows or retro clothing.Application: usually with firm cotton fabricsRequirement: W6 twin needle, size 2.0Sewing machine setting:Attach the cording footInsert the W6 twin needle, size 2.0Thread the twin needle, i.e. use 2 upper threads; thread the 2 upper threads simultaneously, following the normal upper threadline; first separate in the needle on the left and right correspondingly and thread through the 2 needle openings separatelyEnsure that the upper thread can unwind smoothly, i.e. it should be possible to pull out both threads on the leftMark the cording run with chalk, for exampleSew the first cordingAttach the foot at the first sewn cording with the groove of the cording foot; the desired distance corresponds to the selected cording distance. Then use the cording foot to sew down the 2nd cording again; this ensures even cording rowsStitch: Straight stitch (please check whether the twin needle is inserted correctly before starting to sew)Stitch length: 3 - 3.5Thread tension: automatic or 4 in the mechanical models (W6 N 1800, W6 N 1615, W6 N 1233/61, W6 N 1235/61)Tip: For stabilising, put stabiliser under the seam to create an even stitch pattern, if applicable.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines.Application: This foot enables free guidance for free-hand embroidery or darning. It is also ideal for quilting and free-hand quilting.Screw-on the shaft of the presser foot.Use the screw of the shaft of the presser foot to tighten the darning embroidery foot at the needle bar.Let the right bracket run over the right needle bar.Tip 1: Select the full sewing machine speed; this is the only way to ensure that the sewing piece can be easily guided into turns.Tip 2: Please put sufficient stabiliser under the fabric or use an embroidering frame. This prevents any distortion from occurring while sewing.Sewing machine setting:Stitch: Straight stitch or zigzag (width 3-5)Stitch length: not too narrow, as this hinders the sewing machine from rendering a good forward conveyance.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines.Application: This foot ensures a quick and easy gathering of light and elastic fabrics. The cavity behind the needle and the thickening in front of it produce a small raffle.  Sewing machine setting: The gathering depends on the thickness of the fabric, the stitch length and the thread tension, if applicable. Calculation of gathering: The longer the straight stitch, the thicker the gathering. Increase the thread tension, if needed.Set the straight stitchAdjust the needle position to the left (creating a greater distance from the sewn edge)Let the needle pierce the fabric deeplyPull the upper and the lower thread over the left index finger and thus carefully guide the fabric in the beginningCaution: The fabric must be suited for gathering.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: This foot greatly simplifies the hemming of table cloths, handkerchiefs, etc. The helical guide at the top and a groove at the bottom determine the width of the finished hem. The 3-mm folder is ideally suited for light to medium-weight fabrics.Sewing machine setting:Stitch: Straight stitchTip: The desired needle position is determined via the stitch width (check the needle position until the fabric can be seamed).Stitch length: 3-4Procedure: Please make a few straight stitches into the fabric to ensure that the hemming is neat in the beginning. Pull the upper and lower thread created in this way into the spiral, grab the weft at the foot with your left hand, hold it very tightly, and pull the remaining fabric into the spiral until the starting point is under the needle. Insert the needle, lower the foot and start sewing.Tips for sewing corners: First cut all corners a little, but not too much to ensure that they are nut pulled out. Then fold in the fabric edge of the next web side about two times and pull through a strong hand thread. Use this hand thread to pull through the spiral again, hold it tightly and pull it through until the starting point is under the needle. Insert the needle, lower the foot and start sewing.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.This foot has a hollow and transparent middle piece. This can be used for easily guiding applications, darning work and decorative seams, curves or corners.

Presser foot for the W6 WERTARBEIT overlock W6 N 454DApplication: This can be used to sew on decorative bands more easily or to hem bands with the seam in one work step. Great effects with firm fabrics or elastic fabrics. Use the W6 Wertarbeit super stretch 90 needles.Machine setting:Use e.g. the 4-thread seamSet the stitch length to 2.5 to 4Before starting the sewing process, correctly align your elastic or decorative band by loosening the screw of the band guide and inserting your band there.Slide the band up to the end of the presser foot to ensure that the overlock can catch the band when starting the sewing process.With textile bands, the adjusting screw is to be loosened until the band can be pulled through without any resistance.With elastic bands, the adjusting screw is to be tightened until the desired degree of stretching is achieved. This means that it should be possible to pull through the elastic band with medium force while the presser foot is lifted. Please make a trial stitch on the band to see whether it is sewn correctly. With elastic bands, it may be necessary to increase the tension of the needle threads.Always guide the band at the right-hand stop end of the band guide when sewing.Start and end of the seam with rounded-off pieces:Start sewing as described above. Cut off the start of the band that is not sewn on and sew until shortly before the end of the seam. Tip: Cut off the band such that the ends touch each other or overlap slightly.Reinforce the seam by sewing over the already finished seam for about 5 cm.Attachment1. Slightly loosen the screw, do not completely remove it.2. Mount the band guide and tighten the screw3. Mounted band guide4. Insert the elastic band into the band guide and sew it on as described.

Presser foot for W6 WERTARBEIT overlock W6 N 454DApplication: Blind hems require good practice to achieve good results. You can sew these hems with the overlock machine. The foot has an adjustable stop end for perfect edge guidance to ensure ideal hems. Suitable for less elastic and firmer types of fabric.Machine setting:Overlock setting. 4-thread and 3-thread overlock stitch. (standard)Fold the hem at the desired width.Iron this width.Fold the fabric back to the right side of the fabric.Approximately 5-6 mm of the edge should be left here.Place the hem towards the presser foot such that the fold rests against the guide.Adjust the guide such that the needles catch the fold in a straight line.

Presser foot for all W6 WERTARBEIT sewing machines. The W6 N 2000 also requires the adapter.Application: This specially designed foot enables the effortless implementation of overcasting and overlock programmes at the edge of the fabric to be sewn. A neat and even stitch sequence can be easily guaranteed.Sewing machine setting:Stitch: Feather stitchStitch length: Automatic setting of the stitch programme (change if required)Stitch width: 3.5 - 7 (if applicable, check the needle position to ensure that it does not hit the foot’s bar!)In connection with the feather stitch possible with our mechanical models as of W6 N 1800, W6 N 1615, W6 N 1235/61 (and the selection of the stitch length on -SS+), the special construction prevents stretch and elastic fabrics from puckering.The edge enables guiding fabrics evenly.Tip: Before sewing, please ensure that the needle cannot hit the central bar. If needed, change the needle position via the stitch width!Tip: Place a stabiliser under the fabric when working with elastic fabrics that tend to crimp.Please note: The instructions for replacing the presser foot/foot shaft can be found in the manual.